###############################################################################
# Copyright 2006, Way to the Web Limited
# URL: http://www.waytotheweb.com
# Email: sales@waytotheweb.com
###############################################################################
# Testing flag - enables a CRON job that clears iptables incase of
# configuration problems when you start csf. This should be enabled until you
# are sure that the firewall works - i.e. incase you get locked out of your
# server! Then do remember to set it to 0 and restart csf when you're sure
# everything is OK. Stopping csf will remove the line from /etc/crontab
TESTING = "0"
# The interval for the crontab in minutes. Since this uses the system clock the
# CRON job will run at the interval past the hour and not from when you issue
# the start command. Therefore an interval of 5 minutes means the firewall
# will be cleared in 0-5 minutes from the firewall start
TESTING_INTERVAL = "5"
# Enabling auto updates creates a cron job called /etc/cron.d/csf_update which
# runs once per day to see if there is an update to csf+lfd and upgrades if
# available and restarts csf and lfd. Updates do not overwrite configuration
# files or email templates. An email will be sent to the root account if an
# update is performed
AUTO_UPDATES = "0"
# By default, csf will auto-configure iptables to filter all traffic except on
# the local (lo:) device. If you only want iptables rules applied to a specific
# NIC, then list it here (e.g. eth1, or eth+)
ETH_DEVICE = ""
# If you don't want iptables rules applied to specific NICs, then list them in
# a comma separated list (e.g "eth1,eth2")
ETH_DEVICE_SKIP = ""
# Lists of ports in the following comma separated lists can be added using a
# colon (e.g. 30000:35000).
# Allow incoming TCP ports
TCP_IN = "20,21,22,25,53,80,110,143,443,465,953,993,995,2077,2078,2082,2083,2086,2087,2095,2096"
# Allow outgoing TCP ports
TCP_OUT = "20,21,22,25,37,43,53,80,110,113,443,587,873,953,2087,2089,2703"
# Allow incoming UDP ports
UDP_IN = "20,21,53,953"
# Allow outgoing UDP ports
# To allow outgoing traceroute add 33434:33523 to this list 
UDP_OUT = "20,21,53,113,123,873,953,6277"
# Allow incoming PING
ICMP_IN = "1"
# Set the per IP address incoming ICMP packet rate
# To disable rate limiting set to "0"
ICMP_IN_RATE = "1/s"
# Allow outgoing PING
ICMP_OUT = "1"
# Set the per IP address outgoing ICMP packet rate
# To disable rate limiting set to "0"
ICMP_OUT_RATE = "1/s"
# Block outgoing SMTP except for root, exim and mailman (forces scripts/users
# to use the exim/sendmail binary instead of sockets access). This replaces the
# protection as WHM > Tweak Settings > SMTP Tweaks
SMTP_BLOCK = "1"
# If SMTP_BLOCK is enabled but you want to allow local connections to port 25
# on the server (e.g. for web scripts) then enable this option too
SMTP_ALLOWLOCAL = "1"
# If this is a MONOLITHIC kernel (i.e. it has no LKM support, e.g. a VPS) then
# set this to 1. Because of the nature of monolithic kernels, it's not easy to
# determine which modules have been built-in, so some functionality may not be
# available and this firewall script may not work.
#
# One example is if the ip_conntrack and ip_conntrack_ftp iptables kernel
# modules are not available. If this happens, FTP passive mode (PASV) won't
# work. In such circumstances you will have to open a hole in your firewall and
# configure the FTP daemon to use that same hole. For example, with pure-ftpd 
# you could add the port range 30000:35000 to TCP_IN and add the following line
# to /etc/pure-ftpd.conf (without the leading #):
# PassivePortRange	30000 35000
# Then restart pure-ftpd and csf and passive FTP should then work
MONOLITHIC_KERNEL = "0"
# Drop target for iptables rules. This can be set to either DROP ot REJECT.
# REJECT will send back an error packet, DROP will not respond at all. REJECT
# is more polite, however it does provide extra information to a hacker and
# lets them know that a firewall is blocking their attempts. DROP hangs their
# connection, thereby frustrating attempts to port scan the server.
DROP = "DROP"
# Enable logging of dropped connections to blocked ports to syslog, usually
# /var/log/messages. This option needs to be enabled to use Port Scan Tracking
DROP_LOGGING = "1"
# Enable logging of dropped connections to blocked IP addresses in csf.deny or
# by lfd with temporary connection tracking blocks. Do not enable this option
# if you use Port Scan Tracking
DROP_IP_LOGGING = "1"
# Only log reserved port dropped connections (0:1023). Useful since you're not
# usually bothered about ephemeral port drops
DROP_ONLYRES = "1"
# Commonly blocked ports that you do not want logging as they tend to just fill
# up the log file. These ports are specifically blocked (applied to TCP and UDP
# protocols) for incoming connections
DROP_NOLOG = "67,68,111,113,135:139,445,513,520"
# Enable packet filtering for unwanted or illegal packets
PACKET_FILTER = "1"
# Log packets dropped by the packet filtering option PACKET_FILTER. This will
# show packet drops that iptables has deemed INVALID (i.e. there is no
# established TCP connection in the state table), or if the TCP flags in the
# packet are out of sequence or illegal in the protocol exchange.
#
# If you see packets being dropped that you would rather allow then disable the
# PACKET_FILTER option above by setting it to "0"
DROP_PF_LOGGING = "0"
# Enable SYN flood protection. This option configures iptables to offer some
# protection from tcp SYN packet DOS attempts. You should set the RATE so that
# false-positives are kept to a minimum otherwise visitors may see connection
# issues (check /var/log/messages for *SYNFLOOD Blocked*). See the iptables
# man page for the correct --limit rate syntax
SYNFLOOD = "1"
SYNFLOOD_RATE = "20/s"
SYNFLOOD_BURST = "10"
# Enable verbose output of iptables commands
VERBOSE = "1"
# Log lfd messages to SYSLOG in addition to /var/log/lfd.log. You must have the
# perl module Sys::Syslog installed to use this feature
SYSLOG = "0"
# If you wish to allow access from dynamic DNS records (for example if your IP
# address changes whenever you connect to the internet but you have a dedicated
# dynamic DNS record from the likes of dyndns.org) then you can list the FQDN
# records in csf.dyndns and then set the following to the number of seconds to
# poll for a change in the IP address. If the IP address has changed iptables
# will be updated.
# 
# A setting of 600 would check for IP updates every 10 minutes. Set the value
# to 0 to disable the feature
DYNDNS = "0"
# To always ignore DYNDNS IP addresses in lfd blocking, set the following
# option to 1
DYNDNS_IGNORE = "0"
# Enable this option if you wish to allow access from all IP's that have
# authenticated using POP before SMTP (i.e. are valid clients). This option
# checks for IP addresses in /etc/relayhosts, which last for 30 minutes in that
# file after a successful POP authentication.
# 
# Set the value to 0 to disable the feature
RELAYHOSTS = "0"
# Limit the number of IP's kept in the /etc/csf/csf.deny file. This can be
# important as a large number of IP addresses create a large number of iptables
# rules (4 times the number of IP's) which can cause problems on some systems
# where either the the number of iptables entries has been limited (esp VPS's)
# or where resources are limited. This can result in slow network performance,
# or, in the case of iptables entry limits, can prevent your server from
# booting as not all the required iptables chain settings will be correctly
# configured. The value set here is the maximum number of IPs/CIDRs allowed
# if the limit is reached, the entries will be rotated so that the oldest
# entries (i.e. the ones at the top) will be removed and the latest is added.
# The limit is only checked when using csf -d (which is what lfd also uses)
# Set to 0 to disable limiting
DENY_IP_LIMIT = "15"
# Limit the number of IP's kept in the temprary IP ban list. If the limit is
# reached the oldest IP's in the ban list will be removed and allowed
# regardless of the amount of time remaining for the block
# Set to 0 to disable limiting
DENY_TEMP_IP_LIMIT = "15"
# Temporary to Permanent IP blocking. The following enables this feature to
# permanently block IP addresses that have been temporarily blocked
# LF_PERMBLOCK_COUNT times in the last LF_PERMBLOCK_INTERVAL seconds. Set
# LF_PERMBLOCK  to "1" to enable this feature
#
# Care needs to be taken when setting LF_PERMBLOCK_INTERVAL as it needs to be
# at least LF_PERMBLOCK_COUNT multiplied by the longest temporary time setting
# (TTL) for blocked IPs, to be effective
#
# Set LF_PERMBLOCK to "0" to disable this feature
LF_PERMBLOCK = "1"
LF_PERMBLOCK_INTERVAL = "86400"
LF_PERMBLOCK_COUNT = "4"
# Permanently block IPs by network class. The following enables this feature
# to permanently block classes of IP address where individual IP addresses
# within the same class LF_NETBLOCK_CLASS have already been blocked
# LF_NETBLOCK_COUNT times in the last LF_NETBLOCK_INTERVAL seconds. Set
# LF_NETBLOCK  to "1" to enable this feature
#
# This can be an affective way of blocking DDOS attacks launched from within
# the same networ class
#
# Valid settings for LF_NETBLOCK_CLASS are "A", "B" and "C", care and
# consideration is required when blocking network classes A or B
#
# Set LF_NETBLOCK to "0" to disable this feature
LF_NETBLOCK = "0"
LF_NETBLOCK_INTERVAL = "86400"
LF_NETBLOCK_COUNT = "4"
LF_NETBLOCK_CLASS = "C"
# The follow Global options allow you to specify a URL where csf can grab a
# centralised copy of an IP allow or deny block list of your own. You need to
# specify the full URL in the following options, i.e.:
# http://www.somelocation.com/allow.txt
#
# The actual retrieval of these IP's is controlled by lfd, so you need to set
# LF_GLOBAL to the interval (in seconds) when you want lfd to retrieve. lfd
# will perform the retrieval when it runs and then again at the specified
# interval. A sensible interval would probably be every 3600 seconds (1 hour)
#
# You do not have to specify both an allow and a deny file
#
# You can also configure a global ignore file for IP's that lfd should ignore
GLOBAL_ALLOW = ""
GLOBAL_DENY = ""
GLOBAL_IGNORE = ""
LF_GLOBAL = ""
# Enable login failure detection daemon (lfd). If set to 0 none of the other LF
# settings have any effect as the daemon won't start.
# When the trigger level of failures is reached lfd will use csf to add the IP
# to the /etc/csf/csf.deny file and block it
LF_DAEMON = "1"
# The following[*] triggers are application specific. If you set LF_TRIGGER to
# "0" the value of each trigger is the number of failures against that
# application that will trigger lfd to block the IP address
#
# If you set LF_TRIGGER to a value greater than "0" then the following[*]
# application triggers are simply on or off ("0" or "1") and the value of
# LF_TRIGGER is the total cumulative number of failures that will trigger lfd
# to block the IP address
#
# Setting the application trigger to "0" disables it
LF_TRIGGER = "0"
# If LF_TRIGGER is > 1 then the following can be set to "1" to permanently
# block the IP address, or if set to a value greater than "1" then the IP
# address will be blocked temporarily for the value in seconds. For example:
# LF_TRIGGER_PERM = "1" => the IP is blocked permanently
# LF_TRIGGER_PERM = "3600" => the IP is blocked temporarily for 1 hour
#
# If LF_TRIGGER is 0, then the application LF_[application]_PERM value works in
# the same way as above
LF_TRIGGER_PERM = "1"
# To only block access to the failed application instead of a complete block
# for an ip address, you can set the following to "1", but LF_TRIGGER must be
# set to "0" with specific application[*] trigger levels also set
LF_SELECT = "0"
#[*]Enable login failure detection of sshd connections
LF_SSHD = "1"
LF_SSHD_PERM = "1"
#[*]Enable login failure detection of pure-ftpd connections
LF_FTPD = "5"
LF_FTPD_PERM = "1"
#[*]Enable login failure detection of SMTP AUTH connections
LF_SMTPAUTH = "5"
LF_SMTPAUTH_PERM = "1"
#[*]Enable login failure detection of courier pop3 connections. This will not
# trap the older cppop daemon
LF_POP3D = "60"
LF_POP3D_PERM = "1"
#[*]Enable login failure detection of courier imap connections. This will not
# trap the older cpimap (uwimap) daemon
LF_IMAPD = "5"
LF_IMAPD_PERM = "1"
#[*]Enable login failure detection of Apache .htpasswd connections
# Due to the often high logging rate in the Apache error log, you might want to
# enable this option only if you know you are suffering from attacks against
# password protected directories
LF_HTACCESS = "5"
LF_HTACCESS_PERM = "1"
#[*]Enable failure detection of Apache mod_security triggers
# Due to the often high logging rate in the Apache error log, you might want to
# enable this option only if you know you are suffering from attacks against
# web scripts
LF_MODSEC = "5"
LF_MODSEC_PERM = "1"
#[*]Enable login failure detection of cpanel, webmail and whm connections
LF_CPANEL = "5"
LF_CPANEL_PERM = "1"
#[*]Enable detection of suhosin triggers and blocking of attackers
# Example: LF_SUHOSIN = "5"
LF_SUHOSIN = "0"
LF_SUHOSIN_PERM = "1"
# Check that csf appears to have been stopped. This checks the status of the
# iptables INPUT chain. If it's not set to DROP, LF will run csf. This will not
# happen if TESTING is enabled above. The check is done every 300 seconds
LF_CSF = "1"
# Send an email alert if anyone logs in successfully using SSH
LF_SSH_EMAIL_ALERT = "1"
# Send an email alert if anyone uses su to access another account. This will
# send an email alert whether the attempt to use su was successful or not
LF_SU_EMAIL_ALERT = "1"
# Enable scanning of the exim mainlog for repeated emails sent from scripts.
# To use this feature you must add an extended email logging line to WHM >
# Exim Configuration Editor > Switch to Advanced Mode > in the first textbox
# add the following line (without the preceding #):
#
# log_selector = +arguments +subject
#
# If you already use extended exim logging, then you need to either include
# +arguments or use +all
#
# This setting will then send an alert email if more than LF_SCRIPT_LIMIT lines
# appear with the same cwd= path in them within an hour. This can be useful in
# identifying spamming scripts on a server, especially PHP scripts running
# under the nobody account. The email that is sent includes the exim log lines
# and also attempts to find scripts that send email in the path that may be the
# culprit
LF_SCRIPT_ALERT = "1"
# The limit afterwhich the email alert for email scripts is sent. Care should
# be taken with this value if you allow clients to use web scripts to maintain
# psuedo-mailing lists which have large recipients
LF_SCRIPT_LIMIT = "100"
# Enable Directory Watching. This enables lfd to check /tmp and /dev/shm
# directories for suspicious files, i.e. script exploits. If a suspicious
# file is found an email alert is sent. Only one alert per file is sent until
# lfd is restarted, so if you remove a suspicious file, remember to restart lfd
#
# To enable this feature set the following to the checking interval in seconds.
# Set to disable set to "0"
LF_DIRWATCH = "300"
# To remove any suspicious files found during directory watching, enable the
# following. These files will be appended to a tarball in
# /etc/csf/suspicious.tar
LF_DIRWATCH_DISABLE = "0"
# This option allows you to have lfd watch a particular file or directory for
# changes and should they change and email alert using watchalert.txt is sent
#
# To enable this feature set the following to the checking interval in seconds
# (a value of 60 would seem sensible) and add your entries to csf.dirwatch
#
# Set to disable set to "0"
LF_DIRWATCH_FILE = "0"
# This is the interval that is used to flush reports of usernames, files and
# pids so that persistent problems continue to be reported, in seconds.
# A value of 3600 seems sensible
LF_FLUSH = "3600"
# System Integrity Checking. This enables lfd to compare md5sums of the
# servers OS binary application files from the time when lfd starts. If the
# md5sum of a monitored file changes an alert is sent. This option is intended
# as an IDS (Intrusion Detection System) and is the last line of detection for
# a possible root compromise.
#
# There will be constant false-positives as the servers OS is updated or
# monitored application binaries are updated. However, unexpected changes
# should be carefully inspected.
#
# Modified files will only be reported via email once.
#
# To enable this feature set the following to the checking interval in seconds
# (a value of 3600 would seem sensible). This option may increase server I/O
# load onto the server as it checks system binaries.
#
# To disable set to "0"
LF_INTEGRITY = "3600"
# System Exploit Checking. This enables lfd to check for the Random JS Toolkit
# and may check for others in the future:
# http://www.cpanel.net/security/notes/random_js_toolkit.html
# It compares md5sums of the binaries listed in the exploit above for changes
# and also attempts to create and remove a number directory
#
# Modified files will only be reported via email once, though will be reset
# after an hour
#
# To enable this feature set the following to the checking interval in seconds
# (a value of 300 would seem sensible).
#
# To disable set to "0"
LF_EXPLOIT = "300"
# This comma separated list allows you to (de)select which tests LF_EXPLOIT
# performs
#
# For the SUPERUSER check, you can list usernames in csf.suignore to have them
# ignored for that test
#
# Valid tests are:
# JS,SUPERUSER
LF_EXPLOIT_CHECK = "JS,SUPERUSER"
# Set the time interval to track login failures within (seconds), i.e.
# LF_TRIGGER failures within the last LF_INTERVAL seconds
LF_INTERVAL = "300"
# Set the log file parsing interval (seconds). This is how long the daemon
# sleeps before processing the log file entries since the last scan finished
LF_PARSE = "5"
# Send an email alert if an IP address is blocked
LF_EMAIL_ALERT = "1"
# Send an email alert if an account exceeds LT_POP3D/LT_IMAPD logins per hour
# per IP
LT_EMAIL_ALERT = "1"
# Block POP3 logins if greater than LT_POP3D times per hour per account per IP
# address (0=disabled)
#
# This is a temporary block for the rest of the hour, afterwhich the IP is
# unblocked
LT_POP3D = "60"
# Block IMAP logins if greater than LT_IMAPD times per hour per account per IP
# address (0=disabled) - not recommended for IMAP logins due to the ethos
# within which IMAP works. If you want to use this, setting it quite high is
# probably a good idea
#
# This is a temporary block for the rest of the hour, afterwhich the IP is
# unblocked
LT_IMAPD = "0"
# Relay Tracking. This allows you to track email that is relayed through the
# server. It tracks general email sent into the server (RELAY), email sent out
# after POP before SMTP (POPRELAY) and SMTP_AUTH (AUTHRELAY) authentication,
# local email sent from the server (LOCALRELAY). There are also options to send
# alerts and block IP addresses if the number of emails relayed per hour
# exceeds configured limits. The blocks can be either permanent or temporary.