Tüm arkadaşlara tek tek ilgilendikleri için teşekkür ederim.
Hatada bozuk bir dizk görünmüyor. Total kullanım alanın azalmış olabilir mi acaba? Bu hatada sadece rapor sunduğunu görüyorum. Belki boyut azaldığı için uyarıyor olabilir. Onun dışında yazılanlara göre tüm diskler faal durumda.
Total kullanım alanı daha 8 TB civarında var hocam. Alanla ilgili bir sıkıntı yok şimdilik.
6 disk Raid 10 yapınız mevcut sanırım. /dev/sdc Array üzerinde gözükmüyor. Kuvvetle muhtemel /dev/sdc diskiniz arızalı ve işletim sisteminde dahi gözükmüyor.
Her şeyden önce 'smartctl -a /dev/sdc' komutunu uygulamanızı ve /dev/sdc'nin akıbetini görmenizi öneririm.
Disk değiştirildikten sonra partition tablosunu başka bir diskten yeni /dev/sdc'ye kopyalabilir akabinde bu partitionları /dev/mdX altına ekleyebilirsiniz.
[root@ns3378249 ~]# smartctl -a /dev/sdc
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-2.6.32-358.23.2.el6.x86_64] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HUS724040ALE640
Serial Number: PK1331PAG3XJSS
LU WWN Device Id: 5 000cca 22bc1c840
Firmware Version: MJAOA3B0
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Wed Nov 5 12:53:32 2014 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 24) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 569) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 059 059 016 Pre-fail Always - 10788
2 Throughput_Performance 0x0005 138 138 054 Pre-fail Offline - 76
3 Spin_Up_Time 0x0007 134 134 024 Pre-fail Always - 560 (Average 591)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 45
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1995
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 112 112 020 Pre-fail Offline - 38
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 11932
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 45
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 359
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 359
194 Temperature_Celsius 0x0002 162 162 000 Old_age Always - 37 (Min/Max 22/52)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 3819
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1699 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1699 occurred at disk power-on lifetime: 9859 hours (410 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 9a 44 0d Error: UNC 8 sectors at LBA = 0x0d449a00 = 222599680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 9a 44 ed 00 19:28:45.364 READ DMA
ef 10 02 00 00 00 a0 00 19:28:45.363 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 19:28:45.363 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 19:28:45.360 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 19:28:45.360 SET FEATURES [Set transfer mode]
Error 1698 occurred at disk power-on lifetime: 9859 hours (410 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 9a 44 0d Error: UNC 8 sectors at LBA = 0x0d449a00 = 222599680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 9a 44 ed 00 19:28:42.634 READ DMA
ef 10 02 00 00 00 a0 00 19:28:42.633 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 19:28:42.632 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 19:28:42.629 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 19:28:42.629 SET FEATURES [Set transfer mode]
Error 1697 occurred at disk power-on lifetime: 9859 hours (410 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 9a 44 0d Error: UNC 8 sectors at LBA = 0x0d449a00 = 222599680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 9a 44 ed 00 19:28:39.729 READ DMA
ef 10 02 00 00 00 a0 00 19:28:39.728 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 19:28:39.727 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 19:28:39.724 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 19:28:39.724 SET FEATURES [Set transfer mode]
Error 1696 occurred at disk power-on lifetime: 9859 hours (410 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 9a 44 0d Error: UNC 8 sectors at LBA = 0x0d449a00 = 222599680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 9a 44 ed 00 19:28:36.899 READ DMA
ef 10 02 00 00 00 a0 00 19:28:36.897 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 19:28:36.897 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 19:28:36.894 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 19:28:36.894 SET FEATURES [Set transfer mode]
Error 1695 occurred at disk power-on lifetime: 9859 hours (410 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 9a 44 0d Error: UNC 8 sectors at LBA = 0x0d449a00 = 222599680
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 9a 44 ed 00 19:28:34.102 READ DMA
ef 10 02 00 00 00 a0 00 19:28:34.100 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 19:28:34.100 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 19:28:34.097 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 19:28:34.097 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 3760 -
# 2 Short offline Completed without error 00% 3759 -
# 3 Short offline Completed without error 00% 3759 -
# 4 Short offline Completed without error 00% 3759 -
# 5 Short offline Completed without error 00% 3757 -
# 6 Short offline Completed without error 00% 3757 -
# 7 Short offline Completed without error 00% 3682 -
# 8 Short offline Completed without error 00% 3682 -
# 9 Short offline Completed without error 00% 3661 -
#10 Short offline Completed without error 00% 3659 -
#11 Short offline Completed without error 00% 3659 -
#12 Short offline Completed without error 00% 3615 -
#13 Short offline Completed without error 00% 3520 -
#14 Short offline Completed without error 00% 3423 -
#15 Short offline Completed without error 00% 3327 -
#16 Short offline Completed without error 00% 3039 -
#17 Short offline Completed without error 00% 2943 -
#18 Short offline Completed without error 00% 2847 -
#19 Short offline Completed without error 00% 2752 -
#20 Short offline Completed without error 00% 2655 -
#21 Short offline Completed without error 00% 2559 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.dediğiniz sorguyu yapınca bu cevabı alıyorum hocam. OVH çalışanlarına yazdım. Bakalım ne diyecekler...
Ayrıca bu işten çok kıllandım gittim bir tane daha sunucu kiraladım. Ne olur ne olmaz, en azından ona yedekleme filan yaparım...
Teşekkürler ilginize